bidvertiser

Friday, March 19, 2010

MAINTENANCE OR REPAIR OF THE KITCHEN SINK

Let's start with the most common problem most home owners run into, which is a leaking faucet or drain assembly at the kitchen sink.

The leak at the faucet falls into two categories: it drips at the spout or leaks around the handles or base of the spout. There are two basic types of faucets, either "washerless or washer type with a replaceable brass seat. Let's start with the washerless kind since they are the types most used today.

The most popular brand in use in my part of the country is Delta. There are a lot of what I call Delta knockoffs or copies by other companies that can be repaired by Delta parts. Another company which makes washerless faucets is Moen. These are very fine products but I don't recommend doityourselfers to try repairs because to remove the stem, or cartridge, you need a special tool which costs in the neighborhood of forty five dollars.

Starting with Delta and similar types, the most common problem is a drip from the spout. The first thing to do, and I don't mean to insult your intelligence, but be sure the water supply is turned off to the faucet. I hate to admit it but I forgot once and made a terrible mess. Of course I can be excused because I had only done this a few hundred times. This drip means that the seal at the base of the cartride is worn out and needs to be replaced. Remove the Hot or Cold indicator disc on the top of the handle by prying it off with a sharp knife. There will be a screw holding the handle on, usually with a phillips head screw. Remove the screw and knob and set aside. When I do this I replace the seals on both sides (this is for two handle faucets). Now there will be a large nut holding the cartridge down. Remove the nut (I use a pair of channel lock pliers for this). Now don't get ahead here, there will be a raised stub on the cartridge which should be on the inside or toward the spout. This is the handle stop and when it is replaced it needs to have the proper orientation. The cartridge pulls straight up out of the faucet body but sometimes it is hard to get a good grip on the stem so I grasp the stem with my pliers and pull it out that way. Be careful to pull straight up so as not to damage it. Once the cartrige is out you can look into the hole and see the rubber seal in its little hole. There is a spring under the seal also and I take both of them out and replace both. Now this gets tricky. A ball point pen is a pretty good tool to remove the seals snd springs, just push the point into the hole in the center of the seal and it should come out with no problem. I use the ball pen to replace the seals and springs also. The seals go over the springs with the narrow side of the spring into the seal. Assemble one new seal and spring, (obtainable at most any hardware store or lumber yard), and insert your pen into the assembly. Remember, the flanges of the seal go DOWN into the hole. When you hve inserted your assembly into the hole, if you can get a finger next to the pen to hold the assemly in place do that and remove the pen. You may have to work at it a little with your finger to get the seal seated in the hole but it can be done. Once it is seated, install the cartridge making sure it is oriented properly and the little knubs on the side fit into the notches on the body of the faucet. Push down on the top of the stem and see if the cartride is seating into the notches. If it won't go all the way down it means that the seal is not in the hole. Try again. This procedure is the same for a leak around the handle. You just need to replace the cartridge too. If you run into a problem that isn't explained here, post a question and I will answer it to the best of my ability so that all can see it. Thank you for visiting my site. I'm going to have to quit for now but I'll continue this tomorrow

Tuesday, March 16, 2010

Help For Basic Home Maintenance

Welcome to Home Maintenance Basics. I hope I can help you in any home repair or regular maintenance problems you may have, witout you having to spend a fortune or being scammed by an unscrupulous contractor. There are various methods to keeping your homes systems in good shape. The first being regular and consistent upkeep.